Operator by Fibric
Peak Demand
A managed early-access pattern for proposing pre-cooling and staged loads against configured comfort and equipment constraints.
View details
← Marketplace
ConnectorSensing & telemetry
Modbus TCP
Polls holding registers and coils on the meters, drives, and PLCs that already run your plant.
Ask how Modbus TCP fits what you run.
Answers are based on this listing. For anything it can't answer, our team can.
For anything this page can't answer, talk to us.
About
The Modbus TCP connector polls the devices industrial sites have relied on for decades: power meters, variable-frequency drives, PLCs, and sensor gateways. It reads holding and input registers and coil states on a schedule you set per device, applies your register map to turn raw words into named, scaled values, and emits each reading as a governed event with device, register, and timestamp.
Modbus TCP carries no authentication in the protocol, so the connector runs read-only under this listing and reaches only the unit IDs and register ranges on its allow-list, with access scoped at the network layer. It is managed early access: built and maintained by Fibric, and wired with a Fibric deployment engineer through the early-access program.
Highlights
- Polls registers on schedule
- Normalizes meter and drive readings
- Managed target is read-only; downstream actions require a separate governed path
- Provisioned with a deployment engineer through the early-access program
- Kind
- Connector
- Category
- Sensing & telemetry
- Publisher
- Fibric
- Availability
- Early access
- Delivery
- Managed by Fibric; nothing to install
- Data direction
- Read-only
- Pricing
- Early access
- Sold by
- Fibric
- Support
- Developed and supported by Fibric
- Tags
- industrial, protocol, metering, hardware
Authentication
Modbus TCP is unauthenticated by design, so access is scoped at the network layer and constrained by the connector's per-device register allow-list.
What it reads
- Power meter readings: kW, kWh, voltage, current, power factor
- Drive telemetry: speed, torque, fault codes, run hours
- PLC register values and coil states on the polling schedule you define
What it can do
This is a sensing source: it reads, it does not write. Operators act through the write-capable connectors alongside it.
How it works
1
Sense
Power meter readings: kW, kWh, voltage, current, power factor.
2
Reason
Operators reason over this connector's signals next to the rest of your stack, so decisions are grounded in the same records you run on.
3
Act
Nothing. This is a sensing source; operators act through the write-capable connectors alongside it.
Pricing
Managed early access
This listing is informational and not self-serve. A deployment review must validate the connector, credentials, action boundary, recovery path, support, and contractual pricing before use.
- Deployment engineer
- Wires and verifies the integration with you during onboarding
- Managed validation
- Review maturity, authority, supported records, and deployment boundaries before go-live
- Execution records
- Supported reads, proposals, policy decisions, and reported outcomes kept for review
- Support from the builders
- Developed, run, and supported directly by Fibric
Requirements
- IP reachability to each Modbus TCP device or gateway
- A register map (address, type, scaling) for the points you want read
Your deployment engineer verifies each line with you during onboarding.
Support and resources
Supported by the people who built it
This connector is developed, run, and supported by the same Fibric team. Support starts during onboarding with a named deployment engineer and doesn't hand you off afterward.
Works with
Listings this is designed to pair with. Each listing has its own live or managed early-access state.
Operator by Fibric
Predictive Maintenance
A managed early-access pattern for reviewing supported telemetry and proposing a maintenance work order before a suspected fault worsens.
View details
Operator by Fibric
Exception Routing
A managed early-access pattern for identifying line exceptions and proposing reroutes, reschedules, or reviewed dispatches.
View details
Control & actuation connector
PLC Command Bridge
A managed reference bridge for vetted controller commands, with stable-key duplicate suppression, local interlocks, and downstream outcome verification.
View details
Sensing & telemetry connector
OPC UA
The industrial standard for shop-floor data: browses the address space, subscribes to nodes, and keeps the model in sync.
View details
This connector is developed, published, and supported by Fibric. It integrates with Modbus TCP through published APIs. Third-party names and logos identify the systems an integration connects to; they are the property of their respective owners, who are not affiliated with Fibric and do not sponsor or endorse this listing. Trademark policy
Bring Modbus TCP into your early-access deployment
Early access means a deployment engineer wires this with you, and it runs propose-only until you approve live actions.